Key Features: - Large Print Volume: 300 x 200 x 250 mm – 11.8 x 7.9 x 9.8” - Unique Designed Printing Bed – For Strong Adhesion & Easy Removal: The heated bed comprises of metal, tempered glass, and Kapton which ensures the maximum adhesion during printing while the flexible top plate makes the removal easy even in the case of very flat objects - Plug & Play Printer, Easy Setup - Mesh Bed Leveling: Simplify the calibration process - LED Status Indicator - 4GB Internal Storage - New Pr3dator Motherboard – For the Maximum Speed: 32 Bit fast for more accurate and precise control. Our mainboard is equipped with the industry leading motor control system, extended features and great interface connections - Raspberry PI is the Engine of the HMI: Enables more flexible developments - Web Interface, IOT: For the industry 4.0 compatibility - 5” Color Touch Screen - Reinforced Steel Frame - Dual Drive: Ensures better filament flow - New Filament Monitoring Sensor: Smooth operation - All-Metal Hotend: Up to 300°C: Exceptional quality printings and less filament jam - Best Warranty in the Industry: 5 years

Key Features: - Large Print Volume: 300 x 200 x 500 mm – 11.8 x 7.9 x 19.7” - Unique Designed Printing Bed – For Strong Adhesion & Easy Removal: The heated bed comprises of metal, tempered glass, and Kapton, this ensures the maximum adhesion during printing, while the flexible top plate makes the removal easy even in the case of very flat objects - Plug & Play Printer: Easy setup - Mesh Bed Leveling: Simplify the calibration process - Easy Setup: Has a bed levelling wizard which helps in the calibration process - LED Status Indicator - 4GB Internal Storage - New Pr3dator Motherboard – For The Maximum Speed: 32 Bit for more accurate and precise control. Our mainboard is equipped with the industry leading motor control system, extended features and great interface connections - Raspberry PI is the Engine of the HMI: Enables more flexible developments - Web Interface, IOT: For the industry 4.0 compatibility - 5” Color Touch Screen

ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230°C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb.

PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 185° C (365°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.

PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210°C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.

PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210°C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.

ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230°C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with silica gel and/or an active dehumidifier to reduce the amount of moisture it can absorb.

PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210° C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.

Laywood is an extrusion material made from 40% recycled wood combined with polymer binders to allow it to melt and print like any other material. It doesn't warp, doesn't shrink, and doesn't require a heated print bed. The finished product can be sanded like ordinary wood and even smells like wood. The color can be varied from light to dark by increasing the printing temperature through its 190 ~ 220°C printing temperature range.

ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending. This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230°C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament. The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS. Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb.