V7 OEM Equivalent to: Laser Toner for select HP printers - Replaces Q2612A(J) - Black - 4,000 pagesPage Yield: 4,000 pagesCompatibility: HP LaserJet - 1010 - 1012 - 1015 - 1018 - 1020 - 1022 - 3015 - 3020 - 3030 - 3050 - 3052 - 3055 - M1005 MFP - M1319

V7 OEM Equivalent to: Laser Toner for select HP printers - Replaces Q7516A (HP 16A) - Black - 12,000 pagesPage Yield: 12,000 pagesCompatibility: HP LaserJet - 5200 Series

V7 OEM Equivalent to: MICR Toner for select HP, Troy printers - Replaces CC364A(M) 0281300001 - Black - 10,000 pagesPage Yield: 10,000 pagesCompatibility: HP LaserJet - P4014 - P4014DN - P4014N - P4015 - P4015DN - P4015N - P4015TN - P4515 - P4515DN - P4015X - P4515N - P4515TN - P4515X - P4515XM

V7 OEM Equivalent to: MICR Toner for select Troy, HP printers - Replaces 0281500001, CE505A(M) 0281500001 - Black - 2,300 pagesPage Yield: 2,300 pagesCompatibility: HP LaserJet - P2030 - P2035 - P2035N - P2055 - P2055D - P2055DN - P2055X

V7 OEM Equivalent to: MICR Toner for select HP, Troy printers - Replaces Q5942A(M), 0281135001 - Black - 10,000 pagesPage Yield: 10,000 pagesCompatibility: HP LaserJet - 4240 - 4240N - 4250 - 4250N - 4250TN - 4250DN - 4250DTN - 4250DTNSL - 4350 - 4350N - 4350DTN - 4350DTNSL

The Hi-Gloss series of PLA filaments add an attractive shine to print projects. With the ideal processing temperatures between 200 ~ 220°C and a diameter of 1.75mm ±0.05mm, these filaments provide a beautiful contrast versus typical opaque PLAs.Print crystals that truly shine, water that glistens, or contrast against flat or opaque colors can bring a new depth to 3D printed projects that can otherwise feel dull or lacking in luster. These filaments are great for sets, minis, art projects, or any prints that need extra depth and beauty of color.

ABS is one of the most commonly used filament types in 3D printing. It has a high tensile strength and good overall toughness. It has a low density and is softer than PLA, which means lower weight and lower cost when printing large models. Hardness is such that no white dot appears when bending.This 1kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.05mm. It has a nominal processing temperature of 230°C (446°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament.The negatives of using ABS is that it can give off a white smoke with a concentrated odor. It is best to ensure that the printing room is well ventilated when using ABS.Additionally, it has a high moisture absorption rate. Depending on the overall humidity level of the printing environment, an opened spool can absorb enough moisture after a couple of days that high temperature printing could cause bubbles or pocks in the extrusion. It is therefore recommended to not open a spool until you are ready to print and to store any unused portion with with silca gel and/or an active dehumidifier to reduce the amount of moisture it can absorb.

PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle.This 1 kg spool features a thickness of 3.0mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 185° C (365°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament.The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.

PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle.This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210°C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament.The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.

PLA is a good choice for a printing material if you are looking for high accuracy and high resolution. It extrudes at lower temperatures, does not require a heated base, and has a very low shrinkage rate (0.3%). PLA is harder than ABS, but is therefore also a bit more brittle.This 1 kg spool features a thickness of 1.75mm ±0.10mm, with a roundness variation of only 0.03mm. It has a nominal processing temperature of 210°C (410°F). Thickness and roundness factors are laser measured at the factory to ensure accuracy over the entire length of the filament.The negatives of using PLA is that it is vulnerable to degradation from moisture, sunlight, and heat. Additionally, it is more prone to overheating during processing, which can cause dripping and drooping if it gets too hot.